Cloth ghost lighting

$ 3.99

Designer

GOODesign

GOODesign is a design studio established in Seoul, Korea by a representative who has been active in product design and 3D CG field for 20 years. As a design company that pursues a reasonable and differentiated digital design, it has always presented a new direction through working with clients such as Hyundai Motor, Siemens Korea and beiersdorf.   This time, we have put out the life product for 3D printing by utilizing various technique design based on the shape of the Class-A surface. These products are especially the result of deep research on the 3D printing dominant shape that can not be mass-produced using a mold.

For Halloween, it would be nice to have lights that create a spooky atmosphere.
So I designed the cloth ghost lighting.
I had this idea a long time ago, but it is very difficult to express the design while printing thinly.
However, after many years of trial and error, I printed in Vase mode and came up with a design that does not require any support, yet expresses the fabric pleats of the ghost clothes well.

Please check the Slicer settings to print this design well before printing.
Print settings were tested with Simplify3D, Cura and Prusa slicer. Please refer to this setting for other printers and slicers.

You can use LED candle light to put the ghost inside.

Happy Halloween with these spooky Cloth ghost lights!

Size= X 93mm, Y 108mm, Z 119mm

Cloth Ghost Lighting Vase Mode Settings
Ender3 Pro / CR-10S Pro Slicing Settings Cura
Quality Layer Height : 0.12mm / Line Width : 0.6mm
Top/Bottom Bottom Layers : 0
Speed Print Speed : 40.0mm/s
Special Modes Spiralize Outer Contour / Smooth Spiralized Contours : Check
Ender3 Pro / CR-10S Pro Slicing Settings Simplify 3D
Extruder Extrusion Multiplier : 1.2mm / Extrusion width : Auto or Manual 0.48mm
Retraction : Uncheck
Layer Layer Height : 0.1mm / Top Solid : 6 / Bottom Solid : 0 / Outline : 1
Single outline corkscrew printing mode(vase mode) : Check
Speeds Adjust printing speed for layers below 15.0 sec
Allow speed reductions down to 40%
PRUSA Slicing Settings Simplify 3D
Extruder Extrusion Multiplier : 1.2mm / Extrusion width : Auto or Manual 0.48mm
Retraction : Uncheck
Layer Layer Height : 0.1mm / Top Solid : 6 / Bottom Solid : 0 / Outline : 1
Single outline corkscrew printing mode(vase mode) : Check
Speeds Default Printing Speed : 3000mm/min
Outline Underspeed : 40%
PRUSA Slicing Settings PrusaSlicer
Print Settings Expert : Check
Layers and perimeters Layer height : 0.1mm
Spiral vase : Check
Solid layers : Top : 0, Bottom : 0
Advanced Default extrusion width : 0.48mm
First layer : 0.48mm
Perimeters : 0.48mm
External perimeters : 0.48
Infill/perimeters overlap : 35%
Filament Settings Expert : Check
Filament Extrusion multiplier : 1.2
File
File 12.4 MB
Average Time
[0.1mm] Ghost : 4h
[0.1mm] Ghost Stand : 3h 30m
  • Nicolaj.valeur6649
    2021-11-13 06:54:51

    Which colour would you recommend? :-)

  • crayo
    2021-10-31 16:56:21

    printed this, did not come out great, only had ABS in white so may be that.
    shoulders have holes

  • sukalac
    2021-10-27 02:58:23

    Printed beautifully on my MK3s using the specified parameters except for a small hole occurring right at the very top of the print both times I printed it. A small drop of white glue solved the problem.

  • Jrweikle
    2021-10-26 07:41:59

    I made this came out great....everything i have ordered has been spot on

  • alex.sievewright19513
    2021-10-25 17:34:55

    Printed great quality is spot on cheers

  • tozol
    2021-10-19 21:11:32

    quick question..
    using cura 4.8
    on an ender 3 pro, that prints great.

    however just started this, and im getting terible small blobs all round the ghost.
    its only half done but im going to stop t.

    any ideas why im getting the blobs, there in no pertiucular pattern, but they are all round, and i have no ide why>
    could it be one of my setings in cura.

    Ghrayfahx
    2021-10-23 14:12:43

    If you have power loss recovery on it will do that when using vase mode. It pauses every so often to save it’s data to the SD card. Normally it does it at layer changes but there is no layer change on vase mode so it happens in random spots instead.

Notice !

Feel free to talk about your product.
Comments that are irrelevant to the topic may be deleted

did you make it? please write making story !